ESBQLL31-K80C_100G QSFP28_SFP光模块_产品中心

ESBQLL31-K80C

QSFP28 100Gb/s ZR4 80km DDMI

产品特性：
4 lane MUX/DEMUX design
Supports 100GBASE-ZR4 for line rate of 103.125Gb/s
LAN WDM EML laser and PIN receiver with SOA
Aggregate bandwidth of >100Gb/s
LC duplex connector
Up to 80km transmission on single mode fiber
Operating case temperature: 0℃ to 70℃
Single 3.3V power supply
RoHS compliant part
Supports FEC(Forward Error Correction)

立即咨询返回列表

产品概述产品特性技术规格

产品概述

I. 引导图

Diagram of Host Board Connector Block Pin Numbers and Name

II. 引用说明

Pin	Logic	Symbol	Description	Notes
1		GND	Ground	1
2	CML-I	Tx2n	Transmitter Inverted Data Input
3	CML-I	Tx2p	Transmitter Non-Inverted Data Input
4		GND	Ground	1
5	CML-I	Tx4n	Transmitter Inverted Data Input
6	CML-I	Tx4p	Transmitter Non-Inverted Data Input
7		GND	Ground	1
8	LVTLL-I	ModSelL	Module Select
9	LVTLL-I	ResetL	Module Reset
10		Vcc Rx	+3.3V Power Supply Receiver
11	LVCMOS-I/O	SCL	2-wire serial interface clock
12	LVCMOS-I/O	SDA	2-wire serial interface data
13		GND	Ground	1
14	CML-O	Rx3p	Receiver Non-Inverted Data Output
15	CML-O	Rx3n	Receiver Inverted Data Output
16		GND	Ground	1
17	CML-O	Rx1p	Receiver Non-Inverted Data Output
18	CML-O	Rx1n	Receiver Inverted Data Output
19		GND	Ground	1
20		GND	Ground	1
21	CML-O	Rx2n	Receiver Inverted Data Output
22	CML-O	Rx2p	Receiver Non-Inverted Data Output
23		GND	Ground	1
24	CML-O	Rx4n	Receiver Non-Inverted Data Output
25	CML-O	Rx4p	Receiver Inverted Data Output
26		GND	Ground	1
27	LVTTL-O	ModPrsL	Module Present
28	LVTTL-O	IntL	Interrupt
29		Vcc Tx	+3.3V Power supply transmitter	2
30		Vcc1	+3.3V Power supply	2
31	LVTTL-I	LPMode	Low Power Mode
32		GND	Ground	1
33	CML-I	Tx3p	Transmitter Non-Inverted Data Input
34	CML-I	Tx3n	Transmitter Inverted Data Input
35		GND	Ground	1
36	CML-I	Tx1p	Transmitter Non-Inverted Data Input
37	CML-I	Tx1n	Transmitter Inverted Data Input
38		GND	Ground	1

Notes:

1. GND is the symbol for single and supply(power) common for QSFP28 modules. All are common within the QSFP28 module and all module voltages are referenced to this potential otherwise noted.Connect these directly to the host board signal common ground plane.Laser output disabled on TDIS>2.0V or open,enabled on TDIS<0.8V.

2. VccRx,Vcc1 and VccTx are the receiver and transmitter power suppliers and shall be applied concurrently. Recommended host board power supply filtering is shown below.VccRx,Vcc1 and VccTx may be internally connected within the QSFP28 transceiver module in any combination.The connector pins are each rated for maximum current of 500mA.

III. 极限参数

Parameter	Symbol	Min.	Typ.	Max.	Unit	Ref.
Storage Temperature	T_S	-40		85	ºC
Storage Ambient Humidity	H_A	0		85	%	1
Power Supply Voltage	V_CC	-0.5		4	V

Note:

1. Non-condensing.

IV. Recommended Operating Conditions

Parameter	Symbol	Min.	Typ.	Max.	Unit	Ref.
Case Operating Temperature	TOP	0	-	70	ºC
Power Supply Voltage	Vcc	3.13	3.3	3.47	V
Power Supply Current	Icc		1200	1800	mA
Power Dissipation	PD			6.5	W
Transmission Distance	TD		-	80	km

V. Electrical Interface Characteristics电气特性 (EOT,TOP = 0 to +70 ℃ , VCC = 3.135 to 3.465 Volts)

Parameter	Symbol	Min.	Type	Max.	Unit	Ref.
Data Rate per Channel	-		25.78125		Gbps	1
Power Consumption	-	-	4	6.5	W
Supply Current	Icc	-	1.2	1.8	A
Control I/O Voltage-High	VIH	2.0		Vcc	V
Control I/O Voltage-Low	VIL	0		0.7	V
Inter-Channel Skew	TSK			35	Ps
RESETL Duration	-		10		Us
RESETL De-assert time	-			100	ms
Power On Time	-			100	ms
Transmitter
Single Ended Input Voltage Tolerance	-	0.3		VCC	V
Common mode Voltage Tolerance	-	15			mV	2
Transmit Input Diff Voltage	VI	150		1200	mV
Transmit Input Diff Impedance	ZIN	85	100	115
Data Dependent Input Jitter	DDJ		0.3		UI
Receiver
Single Ended Output Voltage Tolerance	-	0.3		4	V
Rx Output Diff Voltage	Vo	370	600	950	mV
Rx Output Rise and Fall Voltage	Tr/Tf			35	Ps	2
Total Jitter	TJ		0.3		UI

Note :

1. For use of 100GBASE-ZR4.

2. 20~80%.

VI. 光学参数(TOP=0 to 70℃，VCC=3.0to 3.6 Volts)

Parameters	Symbol	min	type	max	Unit	Note
Transmitter
Transmit wavelengths	L0	1294.53	1295.56	1296.59	nm
	L1	1299.02	1300.05	1301.09	nm
	L2	1303.54	1304.58	1305.63	nm
	L3	1308.09	1309.14	1310.19	nm
Side-Mode Suppression Ratio	SMSR	30	-	-	dB
Total Average Launch Power	PT	8	-	12.5	dBm
Average launch power, each lane	Pavg	2	-	6.5	dBm
Optical Modulation Amplitude (OMA), each lane		-	-	3	dB
Extinction Ratio	ER	6	-	-	dB
Relative Intensity Noise	Rin			-130	dB/Hz
Average Launch Power OFF Transmitter,each Lane	Roff			-30	dBm
Optical return loss tolerance				20	dB
Transmitter reflectance				12	dB
Transmitter eye mask definition {X1,X2, X3, Y1, Y2, Y3}		{0.25, 0.4, 0.45, 0.25, 0.28, 0.4}				1
Receiver
Damage threshold, each lane	THd			5.5	dBm	1
Average receiver power, each lane	R	-28		-7	dBm	1
Receiver sensitivity (AOP), each lane	Sen			-28	dBm
LOS Assert	LOSA	-40			dBm
LOS De-Assert	LOSD			-29	dBm
LOS Hysteresis	LOSH	0.5			dB

Notes:

1. Sensitivity is specified at BER@5E-5 without FEC.

VII. 数字诊断功能

VIII. 推荐电路

IX. 产品尺寸

Mechanical Dimensions

产品特性

4 lane MUX/DEMUX design

Supports 100GBASE-ZR4 for line rate of 103.125Gb/s

LAN WDM EML laser and PIN receiver with SOA

Aggregate bandwidth of >100Gb/s

LC duplex connector

Up to 80km transmission on single mode fiber

Operating case temperature: 0℃ to 70℃

Single 3.3V power supply

RoHS compliant part

Supports FEC(Forward Error Correction)

应用	标准
100GBASE-ZR4	QSFP28 MSA
	IEEE802.3
	ROHS

技术规格

Ordering Information

Package

Product part NO.

Data Rate (Gbps)

Media

Wavelength

(nm)

Transmission Distance(km)

Temperature Range（℃）

QSFP28

ESBQLL31-K80C

4X25

Single-mode fiber

1294.53 ~ 1296.59

1299.02 ~ 1301.09

1303.54 ~ 1305.63

1308.09 ~ 1310.19

0~70

Commercial