产品特性：
Up to 1.25Gb/s data links
The DFB laser transmitter and PIN/TIA receiver
Up to 120km on 9/125µm SMF
Hot-pluggable SFP footprint
Duplex LC/UPC type pluggable optical interface
Low power dissipation
Metal enclosure, for lower EMI
RoHS compliant and lead-free
Support Digital Diagnostic Monitor interface
Single +3.3V power supply
Compliant with SFF-8472
Case operating temperature
Commercial: 0°C to +70°C
Extended: -20°C to +85°C
I. 引导图
Pinout of Connector Block on Host Board
II. 引用说明
Pin | Symbol | Name/Description | Ref. |
1 | V EET | Transmitter Ground (Common with Receiver Ground) | 1 |
2 | T FAULT | Transmitter Fault. Open Drain. Logic “0” indicates normal operation. | 2 |
3 | T DIS | Transmitter Disable. Laser output disabled on high or open. | 3 |
4 | MOD_DEF(2) | Module Definition 2. Data line for Serial ID. | 4 |
5 | MOD_DEF(1) | Module Definition 1. Clock line for Serial ID. | 4 |
6 | MOD_DEF(0) | Module Definition 0. Grounded within the module. | 4 |
7 | Rate Select | No connection required. | |
8 | LOS | Loss of Signal indication. Open Drain. Logic “0” indicates normal operation. | 5 |
9 | VEER | Receiver Ground (Common with Transmitter Ground) | 1 |
10 | VEER | Receiver Ground (Common with Transmitter Ground) | 1 |
11 | VEER | Receiver Ground (Common with Transmitter Ground) | 1 |
12 | RD- | Receiver Inverted DATA out(CML). AC Coupled | |
13 | RD+ | Receiver Non-inverted DATA out(CML). AC Coupled | |
14 | V EER | Receiver Ground (Common with Transmitter Ground) | 1 |
15 | V CCR | Receiver Power Supply | |
16 | V CCT | Transmitter Power Supply | |
17 | V EET | Transmitter Ground (Common with Receiver Ground) | 1 |
18 | TD+ | Transmitter Non-Inverted DATA in. AC Coupled. | |
19 | TD- | Transmitter Inverted DATA in. AC Coupled. | |
20 | V EET | Transmitter Ground (Common with Receiver Ground) | 1 |
Notes:
1. Circuit ground is internally isolated from chassis ground.
2. TX Fault is an open drain output, which should be pulled up with 4.7K – 10KΩ resistor on the host board. Pull up voltage between 2.0V to VccT/R+0.3V. When high, output indicates a laser fault of some kind. Low indicates normal operation. In the low state, the output will be pulled to < 0.8V. When sensing an improper power level in the laser driver, the SFP sets this signal high and turns off the laser. TX-FAULT can be reset with the TX-DISABLE line. The signal is in LVTTL level.
3. TX disable is an input that is used to shut down the transmitter optical output. It is pulled up within the module with 4.7K – 10KΩ resistor. Its states are: Low (0 – 0.8V): Transmitter on; (>0.8, < 2.0V): Undefined; High (2.0V to VccT/R+0.3V): Transmitter Disabled; Open: Transmitter Disabled. The TX-DISABLE signal is high (LVTTL logic “1”) to turn off the laser output. The laser will turn on when TX-DISABLE is low (LVTTL logic “0”).
4. Should be pulled up with 4.7K - 10KΩ on host board to a voltage between 2.0V to VccT/R+0.3V. MOD_DEF (0) pulls line low to indicate module is plugged in.
5. LOS (Loss of Signal) is an open collector/drain output, which should be pulled up with 4.7K – 10KΩ resistor. Pull up voltage between 2.0V to VccT/R+0.3V. When high, this output indicates the received optical power is below the worst-case receiver sensitivity (as defined by the standard in use). Low indicates normal operation. In the low state, the output will be pulled to < 0.8V.
The RX-LOS is high (LVTTL logic “1”) when there is no incoming light from the companion transceiver. This signal is normally used by the system for the diagnostic purpose. The signal is operated in LVTTL level..
III. 极限参数
Parameter | Symbol | Min. | Typ. | Max. | Unit | Ref. |
Storage Temperature | TS | -40 | 85 | ºC | ||
Storage Ambient Humidity | HA | 5 | 95 | % | ||
Power Supply Voltage | VCC | -0.5 | 4 | V | ||
Signal Input Voltage | -0.3 | Vcc+0.3 | V | |||
Lead Soldering Temperature/Time | TSOLD | 260/10 | ºC/sec | 1 | ||
Lead Soldering Temperature/Time | TSOLD | 360/10 | ºC/sec | 2 | ||
Parameter | Symbol | Min. | Typ. | Max. | Unit | Ref. |
Notes:
1. Suitable for wave soldering.
2. Only for soldering by iron.
IV. 工作条件
Parameter | Symbol | Min. | Typ. | Max. | Unit | Ref. |
Case Operating Temperature | Tcase
| 0 | 70 | ºC | FSGCLCxx-Z12C | |
-20 | 85 | FSGCLCxx-Z12E | ||||
Ambient Humidity | HA | 0 | 85 | % | Non-condensing | |
Power Supply Voltage | VCC | 3.14 | 3.3 | 3.46 | V | |
Power Dissipation | P | 0.8 | 1.1 | W | ||
Data Rate | 1.25 | GBd | TX Rate/RX Rate | |||
Transmission Distance | 120 | km | ||||
Coupled Fiber | Single mode fiber | 9/125um G.652 | ||||
Parameter | Symbol | Min. | ||||
V. 传输器规格
Parameter | Symbol | Min. | Typ. | Max. | Unit | Ref. |
Average Output Power | POUT | 0 | +5 | dBm | ||
Extinction Ratio | ER | 9 | dB | |||
Center Wavelength | λC | -7.5 | +7.5 | nm | FSGCLCxx-Z12 Note(1) | |
Note (1) |
DFB Laser | |||||
Side Mode Suppression Ratio | SMSR | 30 | dBm | |||
Spectrum Bandwidth(-20dB) | σ | 1 | nm | |||
Transmitter OFF Output Power | POff | -40 | dBm | |||
Jitter p-p | tJ | |||||
Note (1): “XX” is: 47,49,51,53,55,57,59 and 61
Note (2): Measure at 2^7-1 NRZ PRBS pattern.
Note (3): Transmitter eye mask definition.
VI. 接收器规格
Parameter | Symbol | Min. | Typ. | Max. | Unit | Ref. |
Input Optical Wavelength | λIN | 1260 | 1620 | nm | ||
Receiver Sensitivity | PIN | -32 | dBm | 1 | ||
InputSaturation Power (Overload) | PSAT | -8 | dBm | |||
Damage Input Power | - | 0 | dBm | |||
Loss of Signal Assert | PA | -40 | dBm | |||
Loss of Signal De-assert | PD | -33 | dBm | 2 |
Notes：
1. Measured with Light source 1xx0nm, ER=9dB; BER =<10^-12 @PRBS=2^7-1 NRZ.
2. When LOS De-asserted, the RX data+/- output is signal output.
VII. 数字诊断图
VIII. 数字诊断监控信息
Parameter | Unit | Accuracy |
Case Temperature | ℃ | ±3 |
Supply Voltage | V | ±3% |
Tx Bias Current | mA | ±10% |
Tx Optical Power | dB | ±3 |
Rx Optical Power | dB | ±3 |
IX. 电气接口特性
Parameter | Symbol | Min. | Typ. | Max. | Unit | Ref. |
Transmitter | ||||||
Input Differential Impedance | Rin | 100 | Ω | |||
Differential Data Input Swing | Vin, pp | 180 | 700 | mVP-P | ||
Transmitter Disable Input-High | VDISH | 2 | Vcc+0.3 | V | LVTTL | |
Transmitter Disable Input-Low | VDISL | 0 | 0.8 | V | ||
Transmitter Fault Input-High | VTxFH | 2 | Vcc+0.3 | V | ||
Transmitter Fault Input-Low | VTxFL | 0 | 0.8 | V | ||
Receiver | ||||||
Output Differential Impedance | Rout | 100 | Ω | |||
Differential Data Input Swing | Vout, pp | 300 | 850 | mVP-P | ||
Output Rise/Fall Time 20% - 80% | - | 260 | Ps | |||
LOS Output Voltage-High | VLOSH | 2 | Vcc+0.3 | V | LVTTL | |
LOS Output Voltage-Low | VLOSL | 0 | 0.8 | V | ||
X. 推荐电路图
XI. 机械规格 (Unit: mm)
SFP wire mechanical drawing (Unit: mm)
Up to 1.25Gb/s data links
The DFB laser transmitter and PIN/TIA receiver
Up to 120km on 9/125µm SMF
Hot-pluggable SFP footprint
Duplex LC/UPC type pluggable optical interface
Low power dissipation
Metal enclosure, for lower EMI
RoHS compliant and lead-free
Support Digital Diagnostic Monitor interface
Single +3.3V power supply
Compliant with SFF-8472
Case operating temperature
Commercial: 0°C to +70°C
Extended: -20°C to +85°C
应用 | 标准 |
Switch to Switch Interface | SFP MSA |
Fast Ethernet Switched Backplane Applications | SFF-8472 |
Router/Server Interface | IEEE802.3z |
Other Optical Links | ROHS |
Package | Product part NO. | Data Rate (Gbps) | Media | Wavelength (nm) | Transmission Distance(km) | Temperature Range（℃） | |
SFP | FSGCLCxx-Z12C | 1.25 | single-mode fiber | 1xx0 | 120 | 0~70 | Commercial |
SFP | FSGCLCxx-Z12E | 1.25 | single-mode fiber | 1xx0 | 120 | -20~85 | Extended |
FSGCLCxx-Z12C
Wavelength (nm) | xx | Clasp Color Code | Wavelength (nm) | xx | Clasp Color Code |
1470 | 47 | Gray | 1550 | 55 | Yellow |
1490 | 49 | Purple | 1570 | 57 | Orange |
1510 | 51 | Blue | 1590 | 59 | Red |
1530 | 53 | Green | 1610 | 61 | Brown |
