FSJMLB31-S30C(I)_25G SFP28_SFP光模块_产品中心

FSJMLB31-S30C(I)

SFP28 25Gb/s LR Lite 300m DDM

产品特性：
Supports 25.78Gb/s aggregate bit rate
1310nm DFB Laser transmitter and PIN/TIA receiver
Maximum link length of 300m on
Single Mode Fiber (SMF)
Hot-pluggable SFP28 footprint
Duplex LC receptacles
Single 3.3V power supply
Maximum power dissipation < 1.2W
RoHS-6 compliant and lead-free
I2C management interface
Case operating temperature
Commercial: 0°C to +70°C
Industrial: -40°C to +85°C

立即咨询返回列表

产品概述产品特性技术规格

产品概述

I. 引导图

Pinout of Connector Block on Host Board

II.引用说明

Pin	Symbol	Name/Description	Ref.
1	V EET	Transmitter Ground (Common with Receiver Ground)	1
2	T FAULT	Transmitter Fault.	2
3	T DIS	Transmitter Disable. Laser output disabled on high or open.	3
4	SDA	2-wire Serial Interface Data Line	4
5	SCL	2-wire Serial Interface Clock Line	4
6	MOD_ABS	Module Absent. Grounded within the module	4
7	RS0	No connection required
8	LOS	Loss of Signal indication. Logic “0” indicates normal operation.	5
9	RS1	No connection required
10	V EER	Receiver Ground (Common with Transmitter Ground)	1
11	V EER	Receiver Ground (Common with Transmitter Ground)	1
12	RD-	Receiver Inverted DATA out. AC Coupled
13	RD+	Receiver Non-inverted DATA out. AC Coupled
14	V EER	Receiver Ground (Common with Transmitter Ground)	1
15	V CCR	Receiver Power Supply
16	V CCT	Transmitter Power Supply
17	V EET	Transmitter Ground (Common with Receiver Ground)	1
18	TD+	Transmitter Non-Inverted DATA in. AC Coupled.
19	TD-	Transmitter Inverted DATA in. AC Coupled.
20	V EET	Transmitter Ground (Common with Receiver Ground)	1

Notes:

1. Circuit ground is internally isolated from chassis ground.

2. TFAULT is an open collector/drain output, which is pulled up with a 4.7kΩ – 10kΩ resistor on the

host board, but is grounded inside the SFP+ cable plug.

3. Laser output disabled on TDIS >2.0V or open, enabled on TDIS <0.8V.

4. Should be pulled up with 4.7kΩ – 10kΩ on host board to a voltage between 2.0V and 3.6V.

MOD_ABS pulls line low to indicate module is plugged in.

5. LOS is open collector output. Should be pulled up with 4.7kΩ – 10kΩ on host board to a voltage

between 2.0V and 3.6V. Logic 0 indicates normal operation; logic 1 indicates loss of signal.

III. 极限参数

Parameter	Symbol	Min	Type	Max	Unit	Ref.
Maximum Supply Voltage	Vcc	-0.5		3.6	V
Storage Temperature	TS	-40		85	℃
Relative Humidity	RH	0		85	%

Notes:

1.Limited by the fiber cable jacket, not the activeends.

2.Non-condensing

IV. 光学特性

Parameter	Symbol	Min.	Typ.	Max.	Unit	Ref.
Transmitter
Signaling rate(range)	Sr		25.7825±100ppm		GBd
Center Wavelength	λc	1295	1310	1325	nm
Spectral Width(-20dB)	Pm			1	nm
Average Output Power	Pavg	-7		2	dBm
Extinction Ratio	ER	3.5			dB
Side Mode Suppression Ratio	SMSR	30			dB
Transmitter OFF Output Power	POff			-30	dBm
Transmitter eye mask definition {X1, X2, X3, Y1, Y2, Y3} Hit ratio 5×10-5 hits per sample.		{0.31, 0.4, 0.45, 0.34, 0.38, 0.4}
Receiver
Signaling rate(range)	Sr		25.7825±100ppm		GBd
Center Wavelength	λc	1295	1310	1325	nm
Receiver Sensitivity(OMA)				-10.5	dBm	1
Receiver Reflectance	Rfl			-26	dBm
Loss of Signal Assert	PA	-30			dBm
Loss of Signal De-assert	PD			-13	dBm
LOS Hysteresis	PD- PA	0.5			dB

Note:

1. Hit ratio 5x10-5.

V. 数字诊断图

VI. 数字诊断监控信息

Parameter	Unit	Accuracy
Case Temperature	℃	±3
Supply Voltage	V	±3%
Tx Bias Current	mA	±10%
Tx Optical Power	dB	±3
Rx Optical Power	dB	±3

VII. 电气接口特性

Parameter	Symbol	Min	Type	Max	Unit	Ref.
Supply Voltage	Vcc	3.135	3.3	3.465	V
Supply Current	Icc			300	mA	Commercial
Supply Current	Icc
Transmitter
Input differential impedance	Rin		100			1
Differential data input swing	Vin, pp	100		800	mV
Transmit Disable Voltage	VD	2		VCC	V
Transmit Enable Voltage	VEN	Vee		Vee+0.8	V
Receiver
Differential data output swing	Vout, pp	100		800	mV	2
LOS Fault	VLOS_fault	2		VccHOST	V	3
LOS Normal	VLOS_norm	Vee		Vee+0.8	V	3

Notes:

1. Connected directly to TX data input pins.AC coupling from pins into laser driver IC.

2. Into 100Ω differential termination.

3. LOS is an open collector output. Should be pulled up with 4.7kΩ – 10kΩ on the host board. Normal operation is logic 0; loss of signal is logic 1. Maximum pull-up voltage is 5.5V.

VIII. 推荐接口电路

IX. 产品尺寸 (mm)

SFP wire mechanical drawing (Unit: mm)

产品特性

Supports 25.78Gb/s aggregate bit rate

1310nm DFB Laser transmitter and PIN/TIA receiver

Maximum link length of 300m on Single Mode Fiber (SMF)

Hot-pluggable SFP28 footprint

Duplex LC receptacles

Single 3.3V power supply

Maximum power dissipation < 1.2W

RoHS-6 compliant and lead-free

I2C management interface

Case operating temperature

Commercial: 0°C to +70°C

Industrial: -40°C to +85°C

应用	标准
25GBASE-LR 25G Ethernet	SFP MSA.
CPRI 10	SFF-8472
	RoHS

技术规格

Ordering Information

Package	Product part NO.	Distance	Temperature Range
FSJMLB31-S30C	25.78125	1310	300m
FSJMLB31-S30I	25.78125	1310	300m
*For availability of additional cable lengths, please contact Fibridge.